Threshold

Overview

The term "threshold" as applied to audio refers to a specific volume level where a process begins to take effect. In some cases the threshold is variable by the user and in other cases it is at a "fixed' level. In digital circuitry, the term can apply to the voltage level reached by an input that results in the output changing states. This is an important concept in understanding how jitter can result due to variations in the waveform input to clock recovery circuitry.

Basics

In most cases, a threshold is a specific voltage level. This voltage level is compared to the source voltage level, which may be a waveform in cases where the instantaneous level is important or a processed signal when a more generalized or “average” level is important.

Processing of analog signals for level control typically involves rectifying the AC waveform into aDC waveform and filtering this waveform to create a varying DC level. This level typically represents the “average” or R.M.S. voltage level of the original audio signal, but can also represent the peak level in applications such as audio limiting.

Digital Clock recovery

Ideal “digital” electronic signals have infinitely short time intervals for the transition between a “0” and a “1” and vice-versa. This will be referred to as a change of “state.” This corresponds to the signal voltage varying between very close to ground or “0 volts” and very close to the power supply voltage for the circuitry (5VDC in TTL circuitry). For binary applications, the 0 Volt portion represents a binary “zero” and the 5V portion represents a binary “one.”

Real world signals do not change states in zero time, and this implies that some method must be used to decide when the input signal changes state.

This is accomplished by having a voltage threshold level at the input. Ideally this level would be approximately half of the total voltage available, but for reasons that are beyond the scope of this discussion, they are typically closer to 30-40% of the total voltage range. As the voltage level of the input waveform slopes upward (or downward) it crosses this threshold and at this point in time the output changes state.

Anything that changes the shape of the waveform can affect the relative timing of when the threshold is crossed, which is why the primary cause of jitter in signals transmitted between devices is waveform distortion. The single most important source of waveform distortion is reflections in the transmission chain caused by impedance miss-matches. Use of impedance matched cable and connectors as well as proper termination helps to greatly minimize impedance miss-matches in the chain. Interference caused by electromagnetic or electrostatic pickup on the cable or ground loops between equipment can also result in distortion of the waveform.

Analog Dynamic Range Control

In order to "fit" wide dynamic range audio signals into limited dynamic range recordings; some form of volume level control is necessary.

There are two types of volume control:

1. Manual- typically a "volume" or "Gain" control on the recording device or a device which is feeding the inputs of the recording device.
2. Automatic- Can be any one or a combination of the following: Compressor, limiter, expander/noise gate, analog soft limiting (or "analog saturation"), digital soft saturation.

In the case of compressor, limiter, or expander/noise gate the threshold is typically user-controllable in the form of a "threshold" adjustment or a combination of input and output level controls. Because saturation modes are basically "peak level" controls; their thresholds are generally "fixed" near peak volume level.

The basic premise is that for signals with a volume level lower than the threshold the signal is unchanged. As the volume level increases and exceeds the threshold, the process begins. In some cases, the process is applied in a linear manner where every increase of the input level by one dB results in the same amount of change to the output signal, and in other cases the process has a more "progressive" non-linear effect where the effect is minimal just above the threshold and increases as the input level increase. The saturation modes of Lavry AD converters are an example of non-linear processes. Another example is the "soft-knee" compressor or limiter.

• The one exception in the examples provided is in the case of an expander/noise gate; in which case the signal is unchanged above the threshold and processed below the threshold.

Lavry Products

• LavryGold AD122-96 MX for more information click here
• LavryGold AD122-96 MkIII for more information click here
• LavryBlue MAD-824 for more information click here
• LavryBlack AD11 for more information click here